[2018-4-NEW] Best Cisco 200-105 Dumps ICND2 Exam Actual Test Youtube Will Be More Popular (Question 21 – Question 33)

Preparing your 200-105 dumps? 200-105, Interconnecting Cisco Networking Devices Part 2 (ICND2 v3.0) is a proctored exam offered by pass4itsure Cisco. This exam is specially linked with pass4itsure (ICND2) Cisco certified solutions expert. This exam is available in English, Japanese. Candidates connected with IT field can apply for pass4itsure 200-105 dumps pdf Cisco certification exams, and this is a CCNA Routing & Switching certification technology. The exam is closed book and no outside reference materials are allowed.

Interconnecting Cisco Networking Devices Part 2
Exam Number: 200-105 ICND2
Associated Certifications: CCNA Routing & Switching
Duration: 90 Minutes (55-65 questions)
Available Languages: English, Japanese

Up to the immediate present 200-105 exam cram(21-33)

The following configuration is applied to a Layer 2 Switch: interface fastethernet 0/4
switchport mode access
switchport port-security
switchport port-security mac-address 0000.1111.1111
switchport port-security maximum 2
swithcport port-security
What is the result of the above configuration being applied to the switch?
A. A host with a mac address of 0000.1111.1111 and up to two other hosts can connect to FastEthernet 0/4 simultaneously
B. A host with a mac address of 0000.1111.1111 and one other host can connect to Fast Ethernet 0/4 simultaneously
C. Violating addresses are dropped and no record of the violation is kept
D. The switch can send an SNMP message to the network management station
E. The port is effectively shutdown
200-105 exam Correct Answer: BD

What are the two default metrics used by EIGRP for route selection? (Choose two.)
A. Bandwidth
B. Delay
C. Reliability
D. Load
Correct Answer: AB
EIGRP adds together weighted values of different network link characteristics in order to calculate a metric for
evaluating path selection.

Refer to the exhibit.
100-105 dumps
Host A pings interface S0/0 on router 3, what is the TTL value for that ping?
A. 253
B. 252
C. 255
D. 254
200-105 dumps Correct Answer: A
From the CCNA ICND2 Exam book: andquot;Routers decrement the TTL by 1 every time they forward a packet; if a router decrements the TTL to 0, it throws away the packet. This prevents packets from rota

What Cisco IOS feature can be enabled to pinpoint an application that is causing slow network performance?
B. Netflow
Correct Answer: B
Netflow can be used to diagnose slow network performance, bandwidth hogs and bandwidth utilization quickly with command line interface or reporting tools. Reference: http://www.cisco.com/c/en/us/prod

Refer to the exhibit.
100-105 dumps
Why has this switch not been elected the root bridge for VLAN1?
A. It has more than one interface that is connected to the root network segment.
B. It is running RSTP while the elected root bridge is running 802.1d spanning tree.
C. It has a higher MAC address than the elected root bridge.
D. It has a higher bridge ID than the elected root bridge.
200-105 pdf Correct Answer: D

While you were troubleshooting a connection issue, a ping from one VLAN to another VLAN on the same switch failed. Which command verifies that IP routing is enabled on interfaces and the local VLANs are up?
A. show ip interface brief
B. show ip nat statistics
C. show ip statistics
D. show ip route
Correct Answer: A
Initiate a ping from an end device in one VLAN to the interface VLAN on another VLAN in order to verify that the switch routes between VLANs. In this example, ping from VLAN 2 ( to Interface

Which two are advantages of static routing when compared to dynamic routing? (Choose two.)
A. Configuration complexity decreases as network size increases.
B. Security increases because only the network administrator may change the routing table.
C. Route summarization is computed automatically by the router.
D. Routing tables adapt automatically to topology changes.
E. An efficient algorithm is used to build routing tables, using automatic updates.
F. Routing updates are automatically sent to neighbors.
G. Routing traffic load is reduced when used in stub network links.
200-105 vce Correct Answer: BG
When reading (or being lectured about) all the glorious details of dynamic routing protocols, it\’s hard not to come away with the impression that dynamic routing is always better than static routing

Refer to the topology. Your company has connected the routers R1. R2. and R3 with serial links. R2 and R3 are connected to the switches SW1 and SW2, respectively. SW1 and SW2 are also connected to the routers R4 and R5. The EIGRP routing protocol is configured. You are required to troubleshoot and resolve the EIGRP issues between the various routers.
Use the appropriate show commands to troubleshoot the issues.
100-105 dumps
100-105 dumps
100-105 dumps
100-105 dumps
100-105 dumps
Router R6 does not form an EIGRP neighbor relationship correctly with router R1. What is the cause for this misconfiguration?
A. The K values mismatch.
B. The AS does not match.
C. The network command is missing.
D. The passive-interface command is enabled.
Correct Answer: C

What are two drawbacks of implementing a link-state routing protocol? (Choose two.)
A. the sequencing and acknowledgment of link-state packets
B. the high volume of link-state advertisements in a converged network
C. the requirement for a hierarchical IP addressing scheme for optimal functionality
D. the high demand on router resources to run the link-state routing algorithm
E. the large size of the topology table listing all advertised routes in the converged network
200-105 exam Correct Answer: CD

Which term describes a spanning-tree network that has all switch ports in either the blocking or fowarding state?
A. converged
B. redundant
C. provisioned
D. spanned
Correct Answer: A
Spanning Tree Protocol convergence (Layer 2 convergence) happens when bridges and switches have transitioned to
either the forwarding or blocking state. When layer 2 is converged, root bridge is elec

Question No : 31 – (Topic 1)
Refer to the exhibit.
100-105 dumps
The output that is shown is generated at a switch. Which three statements are true? (Choose three.)
A. All ports will be in a state of discarding, learning, or forwarding.
B. Thirty VLANs have been configured on this switch.
C. The bridge priority is lower than the default value for spanning tree.
D. All interfaces that are shown are on shared media.
E. All designated ports are in a forwarding state.
F. This switch must be the root bridge for all VLANs on this switch.
200-105 dumps Answer: A,C,E
From the output, we see that all ports are in Designated role (forwarding state) -> A and E are correct. The command “show spanning-tree vlan 30 only shows us information about VLAN 30. We don’t know how many VLAN exists in this switch -> B is not correct. The bridge priority of this switch is 24606 which is lower than the default value bridge priority 32768 -> C is correct. All three interfaces on this switch have the connection type “p2p”, which means Point-to point environment – not a shared media -> D is not correct. The only thing we can specify is this switch is the root bridge for VLAN 3o but we can not
guarantee it is also the root bridge for other VLANs -> F is not correct.

Question No : 32 – (Topic 1)
Which port state is introduced by Rapid-PVST?
A. learning
B. listening
C. discarding
D. forwarding
Answer: C
Spanning Tree from PVST+ to Rapid-PVST Migration Configuration Example
Reference 1:
Reference 2:
PVST+ is based on IEEE802.1D Spanning Tree Protocol (STP). But PVST+ has only 3 port states (discarding, learning and forwarding) while STP has 5 port states (blocking, listening, learning, forwarding and disabled). So discarding is a new port state in PVST+.
100-105 dumps

Background Information
802.1D Spanning Tree Protocol (STP) has a drawback of slow convergence. Cisco Catalyst switches support three types of STPs, which are PVST+, rapid-PVST+ and MST. PVST+ is based on IEEE802.1D standard and includes Cisco proprietary extensions such
as BackboneFast, UplinkFast, and PortFast. Rapid-PVST+ is based on IEEE 802.1w standard and has a faster convergence than 802.1D. RSTP (IEEE 802.1w) natively includes most of the Cisco proprietary enhancements to the 802.1D Spanning Tree, such
as BackboneFast and UplinkFast. Rapid-PVST+ has these unique features: Uses Bridge Protocol Data Unit (BPDU) version 2 which is backward compatible with the 802.1D STP, which uses BPDU version 0. All the switches generate BPDUs and send out on all the ports every 2 seconds, whereas in 802.1D STP only the root bridge sends the configuration BPDUs.
Port Roles—Root port, designated port, alternate port and backup port.
Port States—Discarding, Learning, and Forwarding.
Port Types—Edge Port (PortFast), Point-to-Point and Shared port.
Rapid-PVST uses RSTP to provide faster convergence. When any RSTP port receives legacy 802.1D BPDU, it falls back to legacy STP and the inherent fast convergence benefits of 802.1w are lost when it interacts with legacy bridges.

Question No : 33 – (Topic 1)
Refer to the exhibit.
100-105 dumps
At the end of an RSTP election process, which access layer switch port will assume the discarding role?
A. Switch3, port fa0/1
B. Switch3, port fa0/12
C. Switch4, port fa0/11
D. Switch4, port fa0/2
E. Switch3, port Gi0/1
F. Switch3, port Gi0/2
200-105 pdf Answer: C
In this question, we only care about the Access Layer switches (Switch3 & 4). Switch 3 has a lower bridge ID than Switch 4 (because the MAC of Switch3 is smaller than that of Switch4) so both ports of Switch3 will be in forwarding state. The alternative port will surely belong to Switch4. Switch4 will need to block one of its ports to avoid a bridging loop between the two switches. But how does Switch4 select its blocked port? Well, the answer is based on the BPDUs it receives from Switch3. A BPDU is superior than another if it has:
1. A lower Root Bridge ID2. A lower path cost to the Root3. A lower Sending Bridge ID4. A lower Sending Port ID These four parameters are examined in order. In this specific case, all the BPDUs sent by Switch3 have the same Root Bridge ID, the same path cost to the Root and the same Sending Bridge ID. The only parameter left to select the best one is the Sending Port ID (Port ID = port priority + port index). In this case the port priorities are equal because they use the default value, so Switch4 will compare port index values, which are unique to each port on the switch, and because Fa0/12 is inferior to Fa0/1, Switch4 will select the port connected with Fa0/1 (of Switch3) as its root port and block the other port -> Port fa0/11 of
Switch4 will be blocked (discarding role)

200-105, Interconnecting Cisco Networking Devices Part 2 (ICND2 v3.0) exam is consists of different types of multiple choice questions and answers. In the pass4itsure 200-105 dumps exam resources, It will be the hot test associated with Cisco 200-105 practice exam qualification and you will cover every field and category in Interconnecting Cisco Networking Devices Part 2 (ICND2 v3.0) helping to ready you for your successful CCNA Routing & Switching certification.

[2018-4-NEW Pass4itsure 200-105 PDF Dumps Questions From Google Drive]: https://drive.google.com/open?id=0BwxjZr-ZDwwWWWw0QXQxY3R1X1E

[2018-4-NEW Pass4itsure 200-125 PDF Dumps Questions From Google Drive]: https://drive.google.com/open?id=0BwxjZr-ZDwwWT2VSaUVoODRKR1k

In most cases pass4itsure 200-105 exam collection may include 80% or so of the real test questions. If you master all questions and answers you will get 80% at least. So spending a small amount of time and money in exchange for such a good result is worthful. Please add pass4itsure 200-105 dumps pdf training tool in your shopping cart now. Pass4itsure’s experienced expert team has developed effective training program a for cisco certification 200-105 dumps, which is very fit for candidates.
pass4itsure 200-105 dumps
I will highly recommend you to try pass4itsure.com for your 200-105 dumps for exam preparation. More important is that pass4itsure 200-105 dumps exam answers are applicable to all the IT exam. They provides you 100% valid and accurate 200-105 dumps with money back guarantee in case of failure.
100-105 dumps
Best Pass4itsure Cisco 200-105 Dumps Test Prep, Real Cisco 200-105 Dumps Actual Test Will Be More Popular, We Help You Pass Interconnecting Cisco Networking Devices Part 2 (ICND2 v3.0). Pass4itsure 200-105 Dumps Exam Youtube Free Online Test Here: