Cisco 100-101 Cert, 50% OFF Cisco 100-101 PDF Dumps With The Knowledge And Skills

Welcome to download the newest Pass4itsure 70-341 VCE dumps:

While your study aids will not be audio exams, your Cisco 100-101 exam sample questions will be the perfect Cisco 100-101 exam sample questions study materials to guarantee that you pass. Cisco 100-101 exam sample questions provide you with the experience of taking the actual test. Come to Killtest; choose your like to prepare your Cisco certification exams. Killtest fully loaded Cisco 100-101 exam and Cisco test software are the absolute perfect and preferred way of get yourself ready for the Cisco exams by thousands of successful certified professionals across the world. Just about Cisco 100-101 exam sample questions are backed by our 100% pass guarantee. We guaranteed you will pass your Cisco 100-101 Exam on your first attempt. Get HP certified this week and download HP certification with your computer today.

Which two options will help to solve the problem of a network that is suffering a broadcast storm? (Choose two.)
A. a bridge
B. a router
C. a hub
D. a Layer 3 switch
E. an access point

Correct Answer: BD
What does a host on an Ethernet network do when it is creating a frame and it does not have the destination address?
A. drops the frame
B. sends out a Layer 3 broadcast message
C. sends a message to the router requesting the address
D. sends out an ARP request with the destination IP address

Correct Answer: D
A switch has 48 ports and 4 VLANs. How many collision and broadcast domains exist on the switch (collision, broadcast)?
A. 4, 48
B. 48, 4
C. 48, 1
D. 1, 48
E. 4, 1
Correct Answer: B
Some routers have been configured with default routes. What are some of the advantages of using default routes? (Choose two)
A. They establish routes that will never go down.
B. They keep routing tables small.
C. They require a great deal of CPU power.
D. They allow connectivity to remote networks that are not in the routing table
E. They direct traffic from the internet into corporate networks.
Correct Answer: BD
Refer to the exhibit.
After the power-on-self test (POST), the system LED of a Cisco 2950 switch turns amber. What is the status of the switch?

A. The POST was successful.
B. The switch has a problem with the internal power supply and needs an external power supply to be attached.
C. POST failed and there is a problem that prevents the operating system from being loaded.
D. The switch has experienced an internal problem but data can still be forwarded at a slower rate.
E. The switch passed POST, but all the switch ports are busy.

Correct Answer: C
Refer to the exhibit.
PC1 pings PC2. What three things will CORE router do with the data that is received from PC1? (Choose three.)

A. The data frames will be forwarded out interface FastEthernet0/1 of CORE router.
B. The data frames will be forwarded out interface FastEthernet1/0 of CORE router.
C. CORE router will replace the destination IP address of the packets with the IP address of PC2.
D. CORE router will replace the MAC address of PC2 in the destination MAC address of the frames.
E. CORE router will put the IP address of the forwarding FastEthernet interface in the place of the source IP address in the packets.
F. CORE router will put the MAC address of the forwarding FastEthernet interface in the place of the source MAC address.

Correct Answer: BDF
Which three statements are correct about RIP version 2? (Choose three)
A. It uses broadcast for its routing updates.
B. It supports authentication.
C. It is a classless routing protocol.
D. It has a lower default administrative distance then RIP version 1.
E. It has the same maximum hop count as RIP version 1.
F. It does not send the subnet mask any updates.
Correct Answer: BCE
To what type of port would a cable with a DB-60 connector attach?
A. Serial port
B. Console port
C. Ethernet port
D. Fibre optic port
Correct Answer: A
Which IP address is a private address?
Correct Answer: C
How many simultaneous Telnet sessions does a Cisco router support by default?
A. 1
B. 2
C. 3
D. 4
E. 5
F. 6
Correct Answer: E
Refer to the exhibit.
What two things can the technician determine by successfully pinging from this computer to the IP address (Choose two)
A. The network card on the computer is functioning correctly.
B. The default static route on the gateway router is correctly configured.
C. The correct default gateway IP address is configured on the computer.
D. The device with the IP address is reachable over the network.
E. The default gateway at is able to forward packets to the internet.
Correct Answer: AD
Refer to the exhibit.
Why did the device return this message?

A. The command requires additional options or parameters
B. There is no show command that starts with ru.
C. The command is being executed from the wrong router mode.
D. There is more than one show command that starts with the letters ru.

Correct Answer: D
What is the purpose of flow control?
A. To ensure data is retransmitted if an acknowledgement is not received.
B. To reassemble segments in the correct order at the destination device.
C. To provide a means for the receiver to govern the amount of data sent by the sender.
D. To regulate the size of each segment.

Correct Answer: C
OSPF routing uses the concept of areas. What are the characteristics of OSPF areas? (Chose three)
A. Each OSPF area requires a loopback interface to be configured
B. Areas may be assigned any number from 0 to 65535
C. Area 0 is called the backbone area
D. Hierarchical OSPF networks do not require multiple areas
E. Multiple OSPF areas must connect to area 0
F. Single area OSPF networks must be configured in area 1

Correct Answer: BCE
Part of the OSPF network is shown below:

Configuration exhibit:
R1 routing commands:
ip route serial0/0 router ospf 1 network area 0 network area 0 network area 0 default-information originate
You work as a network technician, study the exhibits carefully. Assume that all router interfaces are operational and correctly configured. In addition, assume that OSPF has been correctly configured on router R2. How will the default route configured on R1 affect the operation of R2?
A. Any packet destined for a network that is not directly connected to router R2 will be dropped immediately.
B. Any packet destined for a network that is not directly connected to router R1 will be dropped.
C. Any packet destined for a network that is not directly connected to router R2 will be dropped immediately because of the lack of a gateway on R1.
D. The network directly connected to a router R2 will not be able to communicate with the, and subnetworks.
E. Any packet destined for a network that is not referenced in the routing table of router R2 will be directed to R1. R1 will then send that packet back to R2 and a routing loop will occur.

Correct Answer: E
Refer to the exhibit.
Which two statements are true about the loopback address that is configured on RouterB? (Choose two)

A. It ensures that data will be forwarded by RouterB.
B. It provides stability for the OSPF process on RouterB.
C. It specifies that the router ID for RouterB should be
D. It decreases the metric for routes that are advertised from RouterB.
E. It indicates that RouterB should be elected the DR for the LAN.

Correct Answer: C
Which characteristics are representative of a link-state routing protocol? (Choose three)
A. provides common view of entire topology
B. exchanges routing tables with neighbors
C. calculates shortest path
D. utilizes event-triggered updates
E. utilizes frequent periodic updates

Correct Answer: ACD

A network associate has configured OSPF with the command:
City(config-router)# network area 0 After completing the configuration, the associate discovers that not all the interfaces are participating in OSPF. Which three of the interfaces shown in the exhibit will participate in OSPF according to this configuration statement? (Choose three)
A. FastEthernet0/0
B. FastEthernet0/1
C. Serial0/0
D. Serial0/1.102
E. Serial0/1.103
F. Serial0/1.104

Correct Answer: BCD
When running OSPF, what would cause router A not to form an adjacency with router B?

A. The loopback addresses are on different subnets.
B. The values of the dead timers on the routers are different.
C. Route summarization is enabled on both routers.
D. The process identifier on router A is different than the process identifier on router.

Correct Answer: B QUESTION 98
Refer to the exhibit.
The network is converged. After link-state advertisements are received from Router_A, what information will Router_E contain in its routing table for the subnets and

A.[110/13] via, 00:00:00:07, FastEthernet0/0[110/13] via, 00:00:00:16, FastEthernet0/0
B.[110/1] via, 00:00:00:07, Serial1/0[110/3] via, 00:00:00:16, FastEthernet0/0
C.[110/13] via, 00:00:00:07, Serial1/0[110/13] via, 00:00:00:16, Serial1/0[110/13] via, 00:00:00:16, FastEthernet0/0
D.[110/13] via, 00:00:00:07, Serial1/0[110/13] via, 00:00:00:16, Serial1/0

Correct Answer: A
Which commands are required to properly configure a router to run OSPF and to add network to OSPF area 0? (Choose two)
A. Router(config)#router ospf 1
B. Router(config)#router ospf 0
C. Router(config)#router ospf area 0
D. Router(config-router)#network area 0
E. Router(config-router)#network 0
F. Router(config-router)#network area 0
Correct Answer: AD
Which parameter or parameters are used to calculate OSPF cost in Cisco routers?
A. Bandwidth, Delay and MTU
B. Bandwidth
C. Bandwidth and MTU
D. Bandwidth, MTU, Reliability, Delay and Load

Correct Answer: B QUESTION 101
Refer to the exhibit.
Why are two OSPF designated routers identified on Core-Router?
A. Core-Router is connected to more than one multi-access network.
B. The router at is a secondary DR in case the primary fails.
C. Two router IDs have the same OSPF priority and are therefore tied for DR election
D. The DR election is still underway and there are two contenders for the role.

Correct Answer: A
What is the default maximum number of equal-cost paths that can be placed into the routing of a Cisco OSPF router?
A. 16
B. 2
C. Unlimited

D. 4
Correct Answer: D
What is the OSPF default frequency, in seconds, at which a Cisco router sends hello packets on a multiaccess network?
A. 10
B. 40
C. 30
D. 20
Correct Answer: A
Refer to the exhibit.
The two connected ports on the switch are not turning orange or green. What would be the most effective steps to troubleshoot this physical layer problem? (Choose three.)

A. Ensure that the Ethernet encapsulations match on the interconnected router and switch ports.
B. Ensure that cables A and B are straight-through cables.
C. Ensure cable A is plugged into a trunk port.
D. Ensure the switch has power.
E. Reboot all of the devices.
F. Reseat all cables.
Correct Answer: BDF
Which command can you use to manually assign a static IPV6 address to a router interface?
A. ipv6 address PREFIX_1::1/64
B. ipv6 autoconfig 2001:db8:2222:7272::72/64
C. ipv6 autoconfig
D. ipv6 address 2001:db8:2222:7272::72/64

Correct Answer: D
The network administrator is using a Windows PC application that is called putty.exe for remote communication to a switch for network troubleshooting. Which two protocols could be used during this communication? (Choose two.)
C. Telnet

Correct Answer: CE
What should be part of a comprehensive network security plan?
A. Allow users to develop their own approach to network security.
B. Physically secure network equipment from potential access by unauthorized individuals.
C. Encourage users to use personal information in their passwords to minimize the likelihood of passwords being forgotten.
D. Delay deployment of software patches and updates until their effect on end-user equipment is well known and widely reported.
E. Minimize network overhead by deactivating automatic antivirus client updates.
Correct Answer: B
Which two of these statements are true of IPv6 address representation? (Choose two.)
A. There are four types of IPv6 addresses: unicast, multicast, anycast, and broadcast.
B. A single interface may be assigned multiple IPv6 addresses of any type.
C. Every IPv6 interface contains at least one loopback address.
D. The first 64 bits represent the dynamically created interface ID.
E. Leading zeros in an IPv6 16 bit hexadecimal field are mandatory.

Correct Answer: BC
A network administrator cannot connect to a remote router by using SSH. Part of the show interfaces command is shown.
router#show interfaces Serial0/1/0 is up, line protocol is down
At which OSI layer should the administrator begin troubleshooting?
A. physical
B. data link
C. network
D. transport
Correct Answer: B
Which option is a valid IPv6 address?
A. 2001:0000:130F::099a::12a
B. 2002:7654:A1AD:61:81AF:CCC1
C. FEC0:ABCD:WXYZ:0067::2A4
D. 2004:1:25A4:886F::1
Correct Answer: D
What is the purpose of the switchport command?
Switch(config-if)# switchport port-security maximum 1Switch(config-if)# switchport port-security mac-address 0018.DE8B.4BF8
A. It ensures that only the device with the MAC address 0018.DE8B.4BF8 will be able to connect to the port that is being configured.
B. It informs the switch that traffic destined for MAC address 0018.DE8B.4BF8 should only be sent to the port that is being configured.
C. It will act like an access list and the port will filter packets that have a source or destination MAC of 0018.DE8B.4BF8.
D. The switch will shut down the port of any traffic with source MAC address of 0018.DE8B.4BF8.
Correct Answer: A
How many bits are contained in each field of an IPv6 address?
A. 24
B. 4
C. 8
D. 16
Correct Answer: D
Which three approaches can be used while migrating from an IPv4 addressing scheme to an IPv6 scheme (Choose three)
A. static mapping of IPv4 address to IPv6 addresses
B. configuring IPv4 tunnels between IPv6 islands
C. use DHCPv6 to map IPv4 addresses to IPv6 addresses
D. use proxying and translation (NAT-PT) to translate IPv6 packets into IPv4 packets
E. configure IPv6 directly
F. enable dual-stack routing

Correct Answer: BDF
Which statement about IPv6 is true?
A. Addresses are not hierarchical and are assigned at random.
B. Only one IPv6 address can exist on a given interface.
C. There are 2.7 billion addresses available.
D. Broadcasts have been eliminated and replaced with multicasts.

Correct Answer: D
What are two recommended ways of protecting network device configuration files from outside network security threats? (Choose two.)
A. Allow unrestricted access to the console or VTY ports.
B. Use a firewall to restrict access from the outside to the network devices.
C. Always use Telnet to access the device command line because its data is automatically encrypted.
D. Use SSH or another encrypted and authenticated transport to access device configurations.
E. Prevent the loss of passwords by disabling password encryption.
Correct Answer: BD
A receiving host has failed to receive all of the segments that it should acknowledge. What can the host do to improve the reliability of this communication session?
A. decrease the window size
B. use a different source port for the session
C. decrease the sequence number
D. obtain a new IP address from the DHCP server
E. start a new session using UDP

Correct Answer: A
Which command enables IPv6 forwarding on a cisco router?
A. ipv6 host
B. ipv6 unicast-routing
C. ipv6 local
D. ipv6 neighbor

Correct Answer: B
Identify the four valid IPv6 addresses. (Choose four.)
A. ::
B. ::192:168:0:1
C. 2000::
D. 2001:3452:4952:2837::
E. 2002:c0a8:101::42
F. 2003:dead:beef:4dad:23:46:bb:101
Correct Answer: ABEF
Which two statements describe characteristics of IPv6 unicast addressing? (Choose two.)
A. Global addresses start with 2000::/3.
B. Link-local addresses start with FE00:/12.
C. Link-local addresses start with FF00::/10.
D. There is only one loopback address and it is ::1.
E. If a global address is assigned to an interface, then that is the only allowable address for the interface.

Correct Answer: AD
A network administrator is trying to add a new router into an established OSPF network. The networks attached to the new router do not appear in the routing tables of the other OSPF routers. Given the information in the partial configuration shown below, what configuration error is causing this problem?
Router(config)# router ospf 1Router(config-router)# network area 0
A. The process id is configured improperly.
B. The OSPF area is configured improperly.
C. The network wildcard mask is configured improperly.
D. The network number is configured improperly.
E. The AS is configured improperly.
F. The network subnet mask is configured improperly.
Correct Answer: C
Which statement is true?
A. An IPv6 address is 64 bits long and is represented as hexadecimal characters.
B. An IPv6 address is 32 bits long and is represented as decimal digits.
C. An IPv6 address is 128 bits long and is represented as decimal digits.
D. An IPv6 address is 128 bits long and is represented as hexadecimal characters.

Correct Answer: D
A network administrator is connecting PC hosts A and B directly through their Ethernet interfaces as shown in the graphic. Ping attempts between the hosts are unsuccessful. What can be done to provide connectivity between the hosts? (choose two.)

A. A crossover cable should be used in place of the straight-through cable.
B. A rollover cable should be used in place of the straight-through cable.
C. The subnet masks should be set to
D. A default gateway needs to be set on each host.
E. The hosts must be reconfigured to use private IP addresses for direct connections of this type.
F. The subnet masks should be set to

Correct Answer: AF
Refer to the exhibit.
A technician pastes the configurations in the exhibit into the two new routers shown. Otherwise, the routers are configured with their default configurations.
A ping from Host1 to Host 2 fails, but the technician is able to ping the S0/0 interface of R2 from Host 1. The configurations of the hosts have been verified as correct. What could be the cause of the problem?

A. The serial cable on R1 needs to be replaced.
B. The interfaces on R2 are not configured properly
C. R1 has no route to the network.
D. The IP addressing scheme has overlapping subnetworks.
E. The ip subnet-zero command must be configured on both routers.

Correct Answer: C
Refer to the exhibit.
Serial 0/0 does not respond to a ping request from a host on the FastEthernet 0/0 LAN. How can this problem be corrected?

A. Enable the Serial 0/0 interface.
B. Correct the IP address for Serial 0/0.
C. Correct the IP address for FastEthernet 0/0
D. Change the encapsulation type on Serial 0/0
E. Enable autoconfiguration on the Serial 0/0 interface

Correct Answer: A
Refer to the exhibit.
What kind of cable should be used to make each connection that is identified by the numbers shown?

A. 1 – Ethernet Crossover cable 2 – Ethernet straight-through cable 3 – Fiber Optic cable 4 – Rollover cable
B. 1 – Ethernet straight-through cable 2 – Ethernet straight-through cable 3 – Serial cable 4 – Rollover cable
C. 1 – Ethernet rollover cable 2 – Ethernet crossover cable 3 – Serial cable 4 – Null-modem cable
D. 1 – Ethernet straight-through cable 2 – Ethernet Crossover cable 3 – Serial cable 4 – Rollover cable
E. 1 – Ethernet straight-through cable 2 – Ethernet Crossover cable 3 – Serial cable 4 – Ethernet Straight-through cable

Correct Answer: B
Which of the following are types of flow control? (choose three.)
A. buffering
B. cut-through
C. windowing
D. congestion avoidance
E. load balancing

Correct Answer: ACD
If an ethernet port on a router was assigned an IP address of, what is the maximum number of hosts allowed on this subnet?
A. 1024
B. 2046
C. 4094
D. 4096
E. 8190
Correct Answer: C QUESTION 128
Refer to the exhibit.
Why was this message received?
A. No VTY password has been set.
B. No enable password has been set.
C. No console password has been set.
D. No enable secret password has been set.
E. The login command has not been set on CON 0
F. The login command has not been set on the VTY ports.

Correct Answer: A
Refer to the exhibit.
How many collision domains are shown?

A. one
B. two
C. three
D. four
E. six
F. twelve

Correct Answer: B
Refer to the exhibit.
After configuring two interfaces on the HQ router, the network administrator notices an error message. What must be done to fix this error?

A. The serial interface must be configured first.
B. The serial interface must use the address
C. The subnet mask of the serial interface should be changed to
D. The subnet mask of the FastEthernet interface should be changed to
E. The address of the FastEthernet interface should be changed to

Correct Answer: D
What does the “Inside Global” address represent in the configuration of NAT?
A. the summarized address for all of the internal subnetted addresses
B. the MAC address of the router used by inside hosts to connect to the Internet
C. a globally unique, private IP address assigned to a host on the inside network
D. a registered address that represents an inside host to an outside network

Correct Answer: D
Two routers named Atlanta and Brevard are connected by their serial interfaces as shown in the exhibit, but there is no data connectivity between them. The Atlanta router is known to have a correct configuration. Given the partial configurations shown in the exhibit, what is the problem on the Brevard router that is causing the lack of connectivity?

A. A loopback is not set.
B. The IP address is incorrect.
C. The subnet mask is incorrect.
D. The serial line encapsulations are incompatible.
E. The maximum transmission unit (MTU) size is too large.
F. The bandwidth setting is incompatible with the connected interface.

Correct Answer: B
Which of the following statements are TRUE regarding Cisco access lists? (Choose two.)
A. In an inbound access list, packets are filtered as they enter an interface.
B. In an inbound access list, packets are filtered before they exit an interface.
C. Extended access lists are used to filter protocol-specific packets.
D. You must specify a deny statement at the end of each access list to filter unwanted traffic.
E. When a line is added to an existing access list, it is inserted at the beginning of the access list.

Correct Answer: AC
Which statements are TRUE regarding Internet Protocol version 6 (IPv6) addresses? (Choose three.)
A. An IPv6 address is divided into eight 16-bit groups.
B. A double colon (::) can only be used once in a single IPv6 address.
C. IPv6 addresses are 196 bits in length.
D. Leading zeros cannot be omitted in an IPv6 address.
E. Groups with a value of 0 can be represented with a single 0 in IPv6 address.

Correct Answer: ABE
Which of the following IP addresses are valid Class B host addresses if a default Class B mask is in use? (Choose two.)
Correct Answer: BE
From which of the following attacks can Message Authentication Code (MAC) shield your network?
A. DoS
C. spoofing
D. SYN floods
Correct Answer: C QUESTION 137
Refer to the exhibit.
A company wants to use NAT in the network shown. Which commands will apply the NAT configuration to the proper interfaces? (Choose two.)

A. R1(config)# interface serial0/1 R1(config-if)# ip nat inside
B. R1(config)# interface serial0/1 R1(config-if)# ip nat outside
C. R1(config)# interface fastethernet0/0 R1(config-if)# ip nat inside
D. R1(config)# interface fastethernet0/0 R1(config-if)# ip nat outside
E. R1(config)# interface serial0/1 R1(config-if)# ip nat outside source pool
F. R1(config)# interface fastethernet0/0 R1(config-if)# ip nat inside source
Correct Answer: BC
How many addresses will be available for dynamic NAT translation when a router is configured with the following commands?
Router(config)#ip nat pool TAME netmask Router(config)#ip nat inside source list 9 pool TAME
A. 7
B. 8
C. 9
D. 10
E. 24
F. 32
Correct Answer: B
Read the scenario and sort the the appropriate commands in order to configure the router.
On the real simulation during the exam you will be required to type the actual commands in order to
configure the router.
Build List and Reorder: Correct Answer:

Whenever Cisco candidates take a tour of sample questions of Cisco 100-101 exam they find their training to be matchless to great extent.Passing the Cisco 100-101 exam on your own can be a difficult task,but with Cisco 100-101 exam preparation products,many candidates who appeared online passed Cisco 100-101 exam easily.

Pass4itsure 070-341 dumps with PDF + Premium VCE + VCE Simulator: